Thingino U-Boot for Ingenic T23N SPL 2013.07-g779c94b (Dec 19 2024 - 23:07:17 PST) nf = 100 nr = 1 od0 = 1 od1 = 2 cppcr is 06405100 nf = 100 nr = 1 od0 = 1 od1 = 2 cppcr is 06405100 apll_freq = 1188000000 mpll_freq = 1200000000 sdram init start DDR clk rate 600000000 image entry point: 0x80100000 Thingino U-Boot for Ingenic 2013.07-g779c94b (Dec 19 2024 - 23:07:17 PST) Architecture: XBurst 1 Platform: ISVP Built profile: T23N SOC Model: T23N DRAM: 64 MiB Top of RAM usable for U-Boot at: 84000000 Reserving 701k for U-Boot at: 83f50000 Reserving 32800k for malloc() at: 81f48000 Reserving 32 Bytes for Board Info at: 81f47fe0 Reserving 124 Bytes for Global Data at: 81f47f64 Reserving 256k for boot params() at: 81f07f64 Stack Pointer at: 81f07f48 Now running in RAM - U-Boot at: 83f50000 MMC: msc: 0 Net: HW address for ETH: 02:4C:EA:2F:45:D5 Net: HW address for WLAN: 02:4C:EA:2F:45:D6 In: serial Out: serial Err: serial KEY: Reset button undefined GPIO: gpio_default: No GPIO env settings provided ETH: Searching for valid PHY ETH: Error: Invalid PHY configuration. ETH: PHY not found! GPIO: gpio_default_net: No GPIO env settings provided GPIO: gpio_mmc_power: No GPIO env settings provided GPIO: gpio_ircut: 52i 53i 49i 50i 57i 58i GPIO: gpio_user: No GPIO env settings provided GPIO: gpio_motor_v: No GPIO env settings provided GPIO: gpio_motor_h: No GPIO env settings provided MMC: Checking for autoupdate files... FAT: loading autoupdate-full.done FAT: loading autoupdate-uboot.bin FAT: loading autoupdate-full.bin JZSFC: Flash chip ID: 856017 SF: Detected P25Q64H (85 60 17 85 00) Erasing flash from address 0x0 to 0x800000 (length: 0x800000) flash write... writing autoupdate-full.done MMC: Flag file autoupdate-full.done created MMC: Auto-update completed successfully. MMC: Checking for kernel image from MMC... MMC: Kernel file not found. MMC: Checking for boot/env files... FAT: loading boot.scr FAT: Unable to read file boot.scr ** FAT: loading uEnv.txt FAT: Unable to read file uEnv.txt ** MMC: Auto-update is set to 'full'. Resetting the device... reset in 4ms Thingino U-Boot for Ingenic T23N SPL 2013.07 (May 04 2026 - 23:11:25 UTC) Probing SoC... T23N nf = 100 nr = 1 od0 = 1 od1 = 2 cppcr is 06405100 nf = 100 nr = 1 od0 = 1 od1 = 2 cppcr is 06405100 apll_freq = 1188000000 mpll_freq = 1200000000 sdram init start DDR clk rate 600000000 image entry point: 0x80100000 Thingino U-Boot for Ingenic 2013.07 (May 04 2026 - 23:11:25 UTC) Architecture: XBurst@I Platform: ISVP Built profile: T23N SOC Model: T23N DRAM: 64 MiB Top of RAM usable for U-Boot at: 84000000 Reserving 694k for U-Boot at: 83f50000 Reserving 32800k for malloc() at: 81f48000 Reserving 32 Bytes for Board Info at: 81f47fe0 Reserving 124 Bytes for Global Data at: 81f47f64 Reserving 256k for boot params() at: 81f07f64 Stack Pointer at: 81f07f48 Now running in RAM - U-Boot at: 83f50000 MMC: msc: 0 JZSFC: Flash chip ID: 856017 SF: Detected P25Q64H 8MB (85 60 17 85 3d) ENV: Warning - bad CRC, using default environment ENV: Saving default environment... ENV: Erasing SPI flash... ENV: Writing to SPI flash... done In: serial Out: serial Err: serial GPIO: gpio_button: 14i RST: Reset button not pressed; skipping factory reset. GPIO: gpio_default: No GPIO env settings provided GPIO: gpio_usb_en: No GPIO env settings provided Net: MAC address for ETH based on device serial set JZSFC: Flash chip ID: 856017 SF: Detected P25Q64H 8MB (85 60 17 85 00) ENV: Erasing SPI flash... ENV: Writing to SPI flash... done Net: MAC address for WLAN based on device serial set ENV: Erasing SPI flash... ENV: Writing to SPI flash... done Net: Networking disabled (U-Boot) GPIO: gpio_default_net: No GPIO env settings provided GPIO: gpio_mmc_power: No GPIO env settings provided GPIO: gpio_ircut: 52i 53i 49i 50i 57i 58i GPIO: gpio_user: No GPIO env settings provided GPIO: gpio_motor_v: No GPIO env settings provided GPIO: gpio_motor_h: No GPIO env settings provided JZSFC: Flash chip ID: 856017 SF: Detected P25Q64H 8MB (85 60 17 85 00) SF: flash_size env set to 8192k SF: flash_sector env set to 4096k SF: probe-alt command completed in 14ms SDU: Checking for autoupdate files... SDU: Checking for u-boot update flag file... FAT: loading autoupdate-uboot.done FAT: Unable to read file autoupdate-uboot.done ** SDU: Checking for u-boot update file... FAT: loading autoupdate-uboot.bin FAT: Unable to read file autoupdate-uboot.bin ** SDU: U-boot update file not found SDU: Checking for full update flag file... FAT: loading autoupdate-full.done 1 bytes read in 5 ms (0 Bytes/s) SDU: Flag file autoupdate-full.done exists, skipping full update MMC: Checking for kernel image from MMC... MMC: Kernel file not found. MMC: Checking for boot/env files... FAT: loading boot.scr FAT: Unable to read file boot.scr ** FAT: loading uEnv.txt FAT: Unable to read file uEnv.txt ** KEY: ###### Press Ctrl-C now to interrupt boot... loading in 1s ###### JZSFC: Flash chip ID: 856017 SF: Detected P25Q64H 8MB (85 60 17 85 00) SF: probe command completed in 6ms SF: 1540096 bytes @ 0x80000 Read: OK SF: read command completed in 496ms ## Booting kernel from Legacy Image at 0x80600000 ... Image Name: Linux-3.10.14__isvp_pike_1.0__ Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1512050 Bytes = 1.4 MiB Load Address: 80010000 Entry Point: 80397290 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.14__isvp_pike_1.0__ (root@0ad7688725c3) (buildroot-gcc-15.2.0) #2 PREEMPT Mon May 4 23:04:44 UTC 2026 [ 0.000000] CPU0 RESET ERROR PC:83F50644 [ 0.000000] CPU0 revision is: 00d00100 (Ingenic Xburst) [ 0.000000] FPU revision is: 00b70000 [ 0.000000] cgu_macphy clk should be opened! [ 0.000000] cgu_vpu clk should be opened! [ 0.000000] CCLK:1188MHz L2CLK:594Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 00448000 @ 00010000 (usable) [ 0.000000] memory: 00038000 @ 00458000 (usable after init) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 02900000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x028fffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x028fffff] [ 0.000000] Primary instruction cache 16kB, 8-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 8-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pls check processor_id[0x00d00100],sc_jz not support! [ 0.000000] MIPS secondary cache 64kB, 8-way, linesize 32 bytes. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 10414 [ 0.000000] Kernel command line: mem=41M@0x0 rmem=23M@0x2900000 console=ttyS1,115200n8 panic=10 root=/dev/mtdblock4 rootfstype=squashfs init=/init mtdparts=jz_sfc:256k(boot),32k(env),224k(config),1504k(kernel),5568k(rootfs),8800k@0x768000(extras),15872k@0x80000(upgrade),16384k@0(all) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 36304k/41984k available (3655k kernel code, 5680k reserved, 725k data, 224k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:351 [ 0.000000] clockevents_config_and_register success. [ 0.000018] Calibrating delay loop... 1185.38 BogoMIPS (lpj=5926912) [ 0.090018] pid_max: default: 32768 minimum: 301 [ 0.090208] Mount-cache hash table entries: 512 [ 0.090705] Initializing cgroup subsys debug [ 0.090726] Initializing cgroup subsys freezer [ 0.092800] devtmpfs: initialized [ 0.094781] regulator-dummy: no parameters [ 0.095158] NET: Registered protocol family 16 [ 0.121834] bio: create slab at 0 [ 0.131878] jz-dma jz-dma: JZ SoC DMA initialized [ 0.133799] usbcore: registered new interface driver usbfs [ 0.134072] usbcore: registered new interface driver hub [ 0.134406] usbcore: registered new device driver usb [ 0.134949] (null): set:249 hold:250 dev=100000000 h=500 l=500 [ 0.135290] (null): set:249 hold:250 dev=100000000 h=500 l=500 [ 0.138744] cfg80211: Calling CRDA to update world regulatory domain [ 0.140632] Switching to clocksource jz_clocksource [ 0.144560] jz-dwc2 jz-dwc2: cgu clk gate get error [ 0.144586] DWC IN OTG MODE [ 0.145446] dwc2 dwc2: Keep PHY ON [ 0.145462] dwc2 dwc2: Using Buffer DMA mode [ 0.145473] dwc2 dwc2: Core Release: 3.00a [ 0.145516] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller [ 0.145554] dwc2 dwc2: new USB bus registered, assigned bus number 1 [ 0.146808] hub 1-0:1.0: USB hub found [ 0.146856] hub 1-0:1.0: 1 port detected [ 0.146997] dwc2 dwc2: DWC2 Host Initialized [ 0.147444] dwc2 dwc2: enter dwc2_gadget_plug_change:2588: plugin = 1 pullup_on = 0 suspend = 0 [ 0.147808] NET: Registered protocol family 2 [ 0.148272] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.148300] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.148315] TCP: Hash tables configured (established 512 bind 512) [ 0.148370] TCP: reno registered [ 0.148386] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.148408] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.148626] NET: Registered protocol family 1 [ 0.148980] RPC: Registered named UNIX socket transport module. [ 0.148994] RPC: Registered udp transport module. [ 0.149000] RPC: Registered tcp transport module. [ 0.149006] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.149783] freq_udelay_jiffys[0].max_num = 10 [ 0.149793] cpufreq udelay loops_per_jiffy [ 0.149800] 12000 59867 59867 [ 0.149806] 24000 119735 119735 [ 0.149813] 60000 299338 299338 [ 0.149819] 120000 598677 598677 [ 0.149826] 200000 997796 997796 [ 0.149832] 300000 1496694 1496694 [ 0.149838] 600000 2993389 2993389 [ 0.149845] 792000 3951274 3951274 [ 0.149851] 1008000 5028895 5028895 [ 0.149858] 1200000 5986779 5986779 [ 0.166143] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.167930] jffs2: version 2.2. © 2001-2006 Red Hat, Inc. [ 0.168718] msgmni has been set to 70 [ 0.170592] io scheduler noop registered [ 0.170633] io scheduler cfq registered (default) [ 0.171371] wait stable.[288][cgu_vpu] [ 0.171385] cgu_vpu can not set to 450000000, will change!!! [ 0.182174] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1 [ 0.249590] dwc2 dwc2: ID PIN CHANGED! [ 0.691769] console [ttyS1] enabled [ 0.696355] logger: created 256K log 'log_main' [ 0.704132] jz TCU driver register completed [ 0.709937] cgu_ssi can not set to 50000000, will change!!! [ 0.715818] usb 1-1: new full-speed USB device number 2 using dwc2 [ 0.722449] the id code = 856017, the flash name is P25Q64H [ 0.728241] JZ SFC Controller for SFC channel 0 driver register [ 0.734711] mtd: jz_sfc: partitioning exceeds flash size, truncating [ 0.741370] mtd: jz_sfc: partitioning exceeds flash size, truncating [ 0.747961] mtd: jz_sfc: partitioning exceeds flash size, truncating [ 0.754628] 8 cmdlinepart partitions found on MTD device jz_sfc [ 0.760817] Creating 8 MTD partitions on "jz_sfc": [ 0.765783] 0x000000000000-0x000000040000 : "boot" [ 0.772263] 0x000000040000-0x000000048000 : "env" [ 0.778607] 0x000000048000-0x000000080000 : "config" [ 0.785319] 0x000000080000-0x0000001f8000 : "kernel" [ 0.792020] 0x0000001f8000-0x000000768000 : "rootfs" [ 0.798684] 0x000000768000-0x000000800000 : "extras" [ 0.805493] 0x000000080000-0x000000800000 : "upgrade" [ 0.812355] 0x000000000000-0x000000800000 : "all" [ 0.818683] SPI NOR MTD LOAD OK [ 0.822608] usbcore: registered new interface driver asix [ 0.828501] usbcore: registered new interface driver cdc_ether [ 0.834869] usbcore: registered new interface driver cdc_ncm [ 0.840968] i2c /dev entries driver [ 0.846139] jz-wdt: watchdog initialized [ 0.851184] TCP: cubic registered [ 0.856142] NET: Registered protocol family 10 [ 0.861719] NET: Registered protocol family 17 [ 0.867809] soc_vpu probe success,version:1.0.0-03203fd46d [ 0.874065] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 0.886611] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.898125] devtmpfs: mounted [ 0.901631] Freeing unused kernel memory: 224K (80458000 - 80490000) [ 0.940737] usb 1-1: device descriptor read/64, error -88 [ 1.240746] usb 1-1: device descriptor read/64, error -88 [ 1.309697] jffs2: notice: (413) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 1.361431] jffs2: notice: (425) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 1.540775] usb 1-1: new full-speed USB device number 3 using dwc2 Starting watchdog Starting LED daemon [ 1.740783] usb 1-1: device descriptor read/64, error -88 Setting initial system time - Mon May 4 23:11:06 GMT 2026 (fail-safe) [ 2.020744] usb 1-1: device descriptor read/64, error -88 Press the [f] key to enter failsafe mode [ 2.320705] usb 1-1: new full-speed USB device number 4 using dwc2 [ 2.740696] usb 1-1: device not accepting address 4, error -88 [ 2.930707] usb 1-1: new full-speed USB device number 5 using dwc2 [ 3.350688] usb 1-1: device not accepting address 5, error -88 [ 3.356772] hub 1-0:1.0: unable to enumerate USB device on port 1 Thingino firmware built for sonoff_s2_t23n_sc2336_atbm6012bx [stable+3875a62, 2026-05-04 23:11:06 +0000] sh: missing ] No LED indicator GPIO found. Applying sysctl settings - Sysctl settings applied Starting seedrng Starting syslogd Remote logging not configured Setting timezone - Timezone name: Etc/GMT - Set TZ to GMT0 - Export TZ globally Generating SSL certificates Generating ECDSA certificate for ing-sonoff-s2 using mbedTLS... mbedtls-certgen -h ing-sonoff-s2.local -c /etc/ssl/certs/uhttpd.crt -k /etc/ssl/private/uhttpd.key -s 256 -t ecdsa -f der SSL certificate generated successfully with mbedTLS Running sysctl: OK Configuring hostname Hostname ing-sonoff-s2 is default and should be generated - Generated name: ing-sonoff-s2-45d6 - Setting hostname to ing-sonoff-s2-45d6 (auto-generated) - Updating current hostname - Hostname in /etc/hosts is ing-sonoff-s2 - Updating hostname in /etc/hosts - Saving hostname in /etc/hostname - Hostname set to ing-sonoff-s2-45d6 Configuring DNS - Using default DNS servers Setting GPIOs Configuring LEDs - Set GPIO 35 off (LED led_b) Configuring USB USB power GPIO is not set in thingino configuration Initializing MMC Load jzmmc_v12 cd_gpio_pin=49 No MMC power GPIO sequence defined Loading kernel modules - Loading exfat  - Loading tx_isp_t23 direct_mode=0 isp_memopt=1 print_level=1 - Loading sensor_sc2336_t23  - Loading audio spk_gpio=7 spk_level=0 Starting Button service Starting dropbear sshd Generating 256 bit ed25519 key, this may take a while... Public key portion is: ssh-ed25519 AAAAC3NzaC1lZDI1NTE5AAAAIJdSekSJh/kbLdTtbojoqGwLc89J6rwgZMzv9Buu/FHc root@ing-sonoff-s2-45d6 Fingerprint: SHA256:aHHfYgvHiLani4GSeIMpIgPDg2xnb4xj5DHX9wVqu0g Configuring mdev Starting Prudynt Starting wireless interface Wireless module GPIO is not set Loading atbm6012bx module with parameters atbm_printk_mask=0 Set MAC address to 02:4c:ea:2f:45:d6 ip: SIOCGIFINDEX: No such device WiFi password missing Starting WPA Supplicant Interface 'wlan0' does not exist. Wireless interface wlan0 not found Starting network Ethernet GPIO does not need a toggle run-parts /etc/network/if-pre-up.d eth0 does not exist or is a USB device, skipping MAC address setup ip link set eth0 up ip: SIOCGIFFLAGS: No such device run-parts /etc/network/if-pre-up.d ip addr add 127.0.0.1/8 dev lo ip link set lo up run-parts /etc/network/if-up.d DHCPv6 disabled on lo run-parts /etc/network/if-pre-up.d ip link set usb0 up ip: SIOCGIFFLAGS: No such device run-parts /etc/network/if-pre-up.d WLAN disabled, no password run-parts: /etc/network/if-pre-up.d/disable_wlan: exit status 1 Starting WireGuard No WireGuard IP address configured Mount /mnt/nfs - Mount share is not set Generating API key Starting NTP daemon - default configuration found - use default configuration - Sync time Starting crond Starting mdnsd Initializing IR-CUT Starting uhttpd SSL certificates found, attempting to start with SSL support... /usr/bin/uhttpd -h /var/www -x /x -t 0 -T 15 -k 10 -n 20 -N 100 -s 443 -C /etc/ssl/certs/uhttpd.crt -K /etc/ssl/private/uhttpd.key -p 80 -E /x/legacy-url-recovery.cgi uhttpd started successfully with SSL support HTTPS: https://ing-sonoff-s2-45d6.local:443/ HTTP: http://ing-sonoff-s2-45d6.local:80/ (redirects to HTTPS) Starting HA daemon Disabled Starting Telegram Bot daemon Starting rc.local Starting Recording Storage Manager Recording storage manager is disabled Starting ONVIF discovery Disabled Starting ONVIF Notify service Checking sysupgrade - Mark sysupgrade complete Queued: PLAY url=/usr/share/sounds/thingino.opus Starting Record service Autostart is not set Heartbeat daemon already running Welcome to Thingino! ing-sonoff-s2-45d6 login: